5s
+1
Submission successful!
|
| Brand Name: | SUNHOUSE |
| Model Number: | Customized |
| Payment Terms: | L/C,T/T |
Film faced plywood is a plywood panel covered with a resin-impregnated surface film, commonly used as a facing material in concrete formwork.
The film provides a smoother, more protected surface than an untreated veneer face. When correctly selected and maintained, it can support easier cleaning and concrete release during formwork operations.
Film faced plywood is widely used in construction systems where a consistent form-facing surface, suitable panel construction and practical handling characteristics are required.
Formwork performance is not determined by the film alone. Core construction, glue-bond durability, panel thickness, support spacing, edge sealing, surface condition, concrete pressure, release agent and handling all influence service life and concrete finish quality.
A film faced plywood panel combines a surface overlay, an internal veneer structure and edge protection. Each part performs a different function.
Surface layer selected for the required finish and formwork conditions. Film type and weight should be confirmed in the product specification.
Layered wood construction that contributes to panel stiffness, consistency and mechanical performance.
Edge coating helps reduce moisture entry through exposed veneer ends and supports panel protection.
Cutting, drilling or edge damage can expose the veneer core. Re-seal damaged or newly cut edges according to the project specification and supplier instructions.
The following parameters help buyers compare different film faced plywood products and select a panel suitable for their construction requirements.
| Parameter | Specification | Performance Consideration |
|---|---|---|
| Thickness | Confirm project requirement (mm) | Influences stiffness and support spacing. |
| Panel Size | Confirm length × width | Impacts formwork layout and joint planning. |
| Film Colour / Type | Phenolic film or other overlay, as declared | Identifies the surface system. Colour alone does not prove resin type. |
| Film Weight | Supplier-declared value and test basis | Helps compare surface specifications. |
| Core Material | Species, ply count and construction | Affects panel consistency and mechanical properties. |
| Bond Classification | Applicable standard and class | Defines bond suitability for moisture exposure. |
| Edge Sealing | Painted / sealed / unsealed | Influences moisture entry through exposed edges. |
| Reuse Expectation | Project-dependent | Depends on handling, concrete pressure, release agent and cleaning. |
Actual mechanical properties, panel dimensions, film weight and bonding performance should be confirmed through product specifications and relevant test records.
Proper handling, installation, cleaning and storage help maintain the surface condition and structural integrity of film faced plywood.
Check film, corners, edges and panel flatness before installation.
Follow engineered support spacing and concrete pressure limits.
Remove concrete residue using non-damaging tools and approved cleaning methods.
Dry, stack flat and repair exposed edges according to supplier instructions.
Never infer a safe support span or load capacity from panel thickness alone. The formwork designer must use verified mechanical properties and project-specific loading conditions.
Film faced plywood is commonly selected as a facing material for different concrete formwork systems. The panel specification should match the project design and working conditions.
Panel facing for concrete wall shuttering systems, with panel layout and support spacing determined by the formwork design.
Deck facing for concrete slab construction when thickness, support spacing and loading conditions are properly engineered.
Cut-to-size panels for column moulds and modular concrete forming systems.
No. The surface film provides additional protection to the panel face, but it does not make the entire plywood board completely waterproof. Cut edges, drilled holes and damaged areas may expose the veneer core. Glue-bond durability and edge protection must be specified separately.
There is no universal reuse count for all film faced plywood products. Actual reuse depends on film quality, core construction, concrete pressure, support design, release agent, cleaning methods, handling and storage. Proper maintenance can help preserve panel condition.
No. Panel thickness alone cannot establish safe load capacity or support spacing. Structural formwork requires verified mechanical properties and a project-specific design that considers concrete pressure, panel dimensions, support arrangement and working conditions.
Film faced plywood has a resin-based surface overlay designed for form-facing applications. Ordinary plywood generally has a veneer surface that may require a separate finish. Their intended uses, surface characteristics and maintenance requirements are different.
The edges expose the internal veneer layers. Unprotected edges can allow moisture to enter the core, particularly after cutting or drilling. Suitable edge protection helps reduce moisture entry and supports better panel maintenance.
The following technical resources provide additional information about plywood construction, bonding quality and moisture-related properties of wood panels.
These references provide general technical information. They do not certify any specific SUNHOUSE product. Product performance and compliance should be supported by the relevant product specifications and test reports.
SUNHOUSE supplies plywood products for construction, furniture and industrial applications. Contact our team to discuss film type, core material, panel thickness, dimensions, bonding requirements and export packaging.
english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
indonesia
tiếng Việt
ไทย
বাংলা
فارسی
polski
